Site Fuel ToolkitOneStopPlant
More

OneStopPlant

How the calculations work

These are the methods behind the three tools. Start with the right measurements: your engine's specified ratio, the inside dimensions of your tank, or a complete set of fuel and hourmeter records.

Petrol and oil mix

A petrol:oil ratio of R:1 means R parts petrol to one part oil. The petrol amount is measured before adding oil; it is not the final amount of mixed fuel.

Oil in ml = petrol in litres × 1,000 ÷ R. To convert oil to litres, divide the ml result by 1,000. If you know the oil amount instead, petrol in litres = oil in ml × R ÷ 1,000.

Use the ratio and oil specification in your machine's manual. The calculator's ratio choices are arithmetic options, not recommendations for particular engines. For a manufacturer's example, STIHL's chainsaw fuel-mix guidance describes one part oil to 50 parts petrol, written there as 1:50. Here that same mixture is labelled 50:1, petrol first. That does not make it the right ratio for every machine.

Example: at a specified 50:1 ratio, 5 litres of petrol needs 5 × 1,000 ÷ 50 = 100 ml of oil. Add that oil to the 5 litres of petrol; do not measure out 5 litres of finished mixture instead.

Open the fuel-mix calculator.

Tank capacity and contents

All three shapes use internal dimensions and a level tank. Capacity is the volume of the complete shape; contents is the volume below the entered liquid depth. Measure depth vertically from the inside bottom. Wall thickness, domed ends, fittings and irregular shapes are not included.

  • Rectangular tank: capacity = length × width × height. Contents = length × width × liquid depth.
  • Upright cylinder: capacity = π × r² × height. Contents = π × r² × liquid depth, where r is half the internal diameter.
  • Horizontal cylinder with flat ends: capacity = π × r² × length. Contents = A × length, where A is the filled circular-segment area below.

For a horizontal cylinder, A = r² × arccos((r − h) ÷ r) − (r − h) × √(2rh − h²). Here r is the internal radius, h is liquid depth, and arccos is measured in radians. Depth must be between 0 and 2r. At zero depth the tank is empty; at depth 2r it is full. Half the depth gives half the volume only at the cylinder's midpoint, not at every depth.

Example: a rectangular tank with internal dimensions 100 cm × 50 cm × 40 cm holds 200 litres geometrically. At 20 cm liquid depth, its contents are 100 litres.

These are elementary geometric volumes, not a tank calibration or a safe filling limit. Leave filling allowances and delivery decisions to the tank's instructions and its actual condition.

Open the tank calculator.

Measured fuel use per hour

Use a full-to-full interval for the same machine. Start with a full tank and an hourmeter reading. Record every addition after that start, including partial top-ups, then finish by filling to the same full level and recording the hourmeter again. Do not count the fuel used to establish the opening full tank.

Litres used = sum of all additions after the opening full tank, including the closing full fill. Measured hours = closing hourmeter − opening hourmeter. Litres per hour = litres used ÷ measured hours; measured hours must be greater than zero.

This balance assumes there were no unrecorded additions, transfers, drains or losses. Keep the fill level consistent and use hourmeter readings, not the time between dates or an estimate of a working day.

Example: start full at 100 hours, add a 12-litre partial top-up, then add 18 litres to return to full at 110 hours. The completed interval uses (12 + 18) ÷ (110 − 100) = 3 L/h. Before that closing full fill, the 12 litres is only a recorded addition, not measured consumption.

For several completed, non-overlapping intervals, the combined rate is sum of litres used ÷ sum of measured hours. Equivalently, weight each interval's L/h by its measured hours. Do not take a simple average of the individual rates. A partial fill cannot close an interval, and litres issued from a store are not automatically litres consumed by a machine.

Open the fuel and hours log.

Units and rounding

One UK imperial gallon is exactly 4.54609 litres. One US liquid gallon is exactly 3.785411784 litres. Choose the named gallon unit rather than treating them as interchangeable.

One metre = 100 centimetres = 1,000 millimetres. Dimensions must use the same length unit before multiplication. One cubic metre = 1,000 litres; one cubic centimetre = 0.001 litres; one cubic millimetre = 0.000001 litres. One litre = 1,000 ml.

A displayed result may be rounded for readability. Extra decimal places do not make a rough measurement more accurate; keep the original measurements and avoid rounding intermediate values when checking the maths.